West-control-solutions TB 40-1 Temperature Monitor Manual de usuario

PMA Prozeß- und Maschinen-Automation GmbHTemperature monitor TB 40-1TB40-1TB40-1Operating manualEnglish9499-040-63411Valid from: 8505

gSaved alarms (Err-LED is lit) can be acknowledged and deleted with the digitalinput di1 or the RESET-key.Configuration, see page : ConF / LOGI / Err.

3.6.2 Alarm handling additional alarmsMax. two alarms can be configured and assigned to the individual outputs. Gene-rally, outputs OuT.1and OuT.2 can

gThe variable to be monitored can be selected seperately for each alarm viaconfigurationThe following variables can be monitored:wprocess valuewcontro

4 Configuration level4.1 Configuration surveyConF Configuration levelÈÌLimLimit value functionsInP.1Input 1OUt.2Output 2OUt.3Output 3LOGIDigital input

4.2 ConfigurationLimName Value range Description DefaultFcn.1Function of limit 133Measured value monitoring + latching of the alarm status ofthe upper

Name Value range Description Default20Pt100 (-200.0 ... 100,0 °C)21Pt100 (-200.0 ... 850,0 °C)22Pt1000 (-200.0 ... 850.0 °C)23special 0...4500 Ohm (pr

othrName Value range Description DefaultUnitUnit10without unit1°C2°FdPDecimal point (max. number of digits behind the decimalpoint)00No digit behind t

5 Parameter setting level5.1 Parameter surveygAdjustment:wThe parameters can be adjusted by means of keys ÈÌwTransition to the next parameter is by pr

5.2 ParametersLimName Value range Description DefaultLC-1999...9999LC limit100L.2-1999...9999Lower limit 2OFFH.2-1999...9999Upper limit 2OFFHYS.20...9

5.3 Input scaling InP.1When using current or voltage signals as input variables for InP.1 scaling ofinput and display values at parameter setting leve

© PMA Prozeß- und Maschinen-Automation GmbH • Printed in GermanyAll rights reserved. No part of this document may be reproduced or published in any fo

6 Calibration levelgMeasured value correction ( CAL) is only visible if ConF / InP.1 / Corr = 1or 2 is chosen.The measured value can be matched in the

Offset correction ( ConF/ InP.1 / Corr =1 ):InL.1: The input value of the scaling point is displayed.The operator must wait, until the process is at r

2-point correction ( ConF/ InP.1 / Corr = 2):InL.1: The input value of the lower scaling point is displayed.The operator must adjust the lower input v

7 BlueControlBlueControl is the projection environment for the BluePortâcontroller series ofPMA. The following 3 versions with graded functionality ar

8 VersionsAccessories delivered with the unitOperating manual (if selected by the ordering code)w2 fixing clampswoperating note in 15 languagesAccesso

9 Technical dataINPUTSPROCESS VALUE INPUT INP1Resolution: > 14 bitsDecimal point: 0 to 3 digits behind the decimal pointDig. input filter: adjustab

AC SUPPLYVoltage: 90...250 V ACFrequency: 48...62 HzPower consumption approx. 7.3 VAUNIVERSAL SUPPLY 24 V UCAC voltage: 20,4...26,4 V ACFrequency: 48.

Technical dataTB40-1 27Range Input resistance Accuracy Resolution (Ô)0-10 Volt ~ 110 kW ß 0,1 % ß 0,6 mV0-20 mA 49 W (voltage requirement ß 2,5 V) ß 0

10 Safety hintsThis unit was built and tested in compliance with VDE 0411-1 / EN 61010-1 andwas delivered in safe condition.The unit complies with Eur

MAINTENANCE, REPAIR AND MODIFICATIONThe units do not need particular maintenance.aWarningWhen opening the units, or when removing covers or components

TB40-1 3Contents1 Mounting ... 42 Electrical connections ... 52.1 Connecting diagram...

10.1 Resetting to factory settingIn case of faulty configuration, TB40-1 can be reset to ist factory the default con-dition.1For this, the operator mu

Index!2-point correction...21AAccessory equipment...25Additional alarms...12Alarm handling ...11-12BBlueControl...

Subject to alterations without notice © PMA Prozeß- und Maschinen-Automation GmbHÄnderungen vorbehalten P.O.B. 310 229, D-34058 Kassel, GermanySous ré

1 MountingSafety switch:For access to the safety switches, the controller must be withdrawn from the hou-sing. Squeeze the top and bottom of the front

2 Electrical connections2.1 Connecting diagram* Safety switch mA i V in position leftgThe controller is fitted with flat-pin terminals 1 x 6,3mm or 2

Connection of input di1 3Digital input, configurable as switch or push-buttonConnection of output OUT LC 4Relay (250V/2A), potential-free changeover c

3 Operation3.1 Front viewLED colours:LED 1, 2, 3: yellowLED OK: greenother LEDs: redgIn the upper display line, theprocess value is alwaysdisplayed (E

3.3 Behavior with sensor break/ measuring circuit errorIf a sensor break/ measuring circuit error is recognized, the process value displaychanges to F

3.5 Maintenance manager / Error listWith one or several errors, the extended operating level al-ways starts with the error list. Signalling an actual